Grand Banks 36 Classic
Built 1964–2004 by Grand Banks Yachts
Is she right for you? Take the quiz
Own one? Start her custom manual
Looking at one? Sea-trial scorecard
About the Grand Banks 36 Classic
Researched from public sources for this model. Any individual boat may have been modified or repowered — confirm before relying on any figure.
- Built
- 1964–2004
- Builder
- Grand Banks Yachts
- Length
- 36.33 ft
- Waterline
- 35.17 ft
- Beam
- 12.17 ft
- Draft
- 4 ft
- Displacement
- 26,000 lb
- Hull
- fiberglass
- Hull / keel
- semi-displacement
- Propulsion
- inboard
- Fuel
- 400 gal
- Water
- 140 gal
- Holding
- 40 gal
- Water heater
- AC + engine
Tank capacities — where the figures come from
-
Fuel 400 gal
“Fuel 400 gal. 1,514 litres” — brochure, murrayyachtsales.com · “With 400 gallons of fuel” — search excerpt (1988), bluewateryachtsales.comGrand Banks' own GB 36 Motor Yacht brochure (American Marine / Grand Banks Yachts, fiberglass era, printed in Singapore) gives 400 gal (1,514 litres). Oxford Yacht Agency's model page and 1988-89 listings (two engine-room saddle tanks) agree. Early wooden boats may differ: a 1968 wooden boat's listing describes 410 gal in three iron tanks.
-
Water 140 gal
“Water 140 gal. 530 litres” — brochure, murrayyachtsales.com · “154 gallons of fresh water” — search excerpt (1988), bluewateryachtsales.com · “140 gal” — spec database, oxfordyachtagency.comThe factory brochure gives 140 gal (530 litres), matching long-time Grand Banks dealer Oxford Yacht Agency. Our earlier 154 came from the HMY powerboat guide and late-1980s listings (one mentions two aluminium tanks); no builder document gives 154. The brochure is undated, so a change between years can't be ruled out.
-
Holding 40 gal
A 1988 listing says 40 gal and a 1989 listing says 35 gal. The factory brochure gives no holding figure, and no builder or owner's-manual source was found.
-
Water heater AC + engine
“6-gallon Raritan hot water heater - A/C & Engine (2021)” — broker listing (1984 boat, heater replaced 2021), denisonyachtsales.com · “Water heater with exchanger” — search excerpt, dreamboatcompany.comNo builder capacity was found; the American Marine Grand Banks 36 Motor Yacht brochure gives only 140 gal water and 400 gal fuel. One broker listing has a 6 gal Raritan AC and engine heater fitted in 2021, a replacement, so not proof of the original size.
Tanks are often replaced or added on older boats — check the tank labels or a survey for yours.
Thrusters and steering — where this comes from
-
Bow thruster unknown
Only one boat was seen with one (a broker listing for a twin-Ford Grand Banks 36 Classic with an electric bow thruster); the builder's GB36 Motor Yacht brochure and 1990 catalogue are silent.
-
Steering unknown
Owner posts on an owners' forum and a Grand Banks owners' Facebook group (possibly about the same 1988 boat) describe original cable steering with a chain-driven autopilot. No builder, association or review source was found, and the GB36 owner's manual couldn't be checked.
Thrusters and steering are often replaced — check the units on your boat before ordering parts.
Grand Banks' first model; mahogany until mid-1973, fiberglass afterwards. Enlarged about 1987-88 (length to 36.83 ft, beam to 12.67 ft). Most have a single Lehman; twins were optional (about 10 knots cruise with twins). Over 1,200 built including wooden hulls. Over 1,200 built including wooden hulls (HMY).
Engines fitted
-
Ford Lehman 120 — 120 hp, diesel, single or twin
standard
HMY: most 36 Classics had a single 120 or 135 hp Lehman; twins also built. One 1984 owner reports a British Leyland 6N125 (125 hp), the same basic engine as the Lehman 120.Sources: hmy.com · trawlerforum.com
-
Ford Lehman SP135 — 135 hp, diesel, single or twin
standard
Early boats came with a single 135 hp Lehman; a 1991 boat is listed with twin SP135s.Sources: hmy.com · denisonyachtsales.com · curtisstokes.net
-
Caterpillar 3208N — 210 hp, diesel, single
factory option
Three separate 1986-1988 boats are listed with a single naturally aspirated 3208; the listings do not say whether it was factory-fitted.Sources: curtisstokes.net · curtisstokes.net · denisonyachtsales.com
-
Cummins 6BT5.9 — 210 hp, diesel, single or twin
factory option
Later-production boats offered larger packages incl. twin 210 hp Cummins; a 1995 boat has a single 6BT5.9M 210 hp. A 1989 boat is listed with twin 6BT at 160 hp (origin not stated).Sources: denisonyachtsales.com · grandyachts.com · breweryacht.com
Boats of the same model can differ — check which engines yours actually has before ordering parts.
Generator
Many broker listings show a generator, but makes and sizes differ: Onan 4 kW (1984 boat), Kohler 8 kW (1981), Northern Lights 5 kW (one listing), a refurbished Northern Lights 8 kW fitted in a refit (1977), and an owners' forum post mentions an Onan. No builder document says whether the factory offered one.
Known problems for this model
-
Water reaching fuel tanks via deck fill fuel
Teak around the deck fuel fill compresses over time and the caulk seal fails, letting water into the sub-deck and onto the tops of the fuel tanks; keep that joint sealed and inspect tanks.trawlerforum.com
-
Teak deck bungs and core rot deck
Loose bungs and screw holes in the teak decks are the usual path for water into the cored deck; owners replace bungs proactively.trawlerforum.com
-
Sun-damaged exterior and interior teak interior
Boats left uncovered in hot climates show failed varnish and delaminating interior teak veneer, which is expensive to restore.trawlerforum.com
Engines & parts
Ford Lehman 120 (6D380 / 2715E) parts: good
Factory standard engine — you entered “Ford Lehman 120”
Marinized by Lehman from the Ford of England 'Dorset' 2715E six-cylinder (380 cu in) industrial/truck diesel; Ford built the Dorset base engines 1964–1984. Base-engine internals interchange with the Ford 2715E, and marine-specific parts (raw water pumps, heat exchangers, injection elbows, gaskets, lift pumps, air filters) are widely stocked. American Diesel Corp (founded by former Lehman people) still sells parts, publishes spare-parts lists and gives technical advice. Rebuilt and used 120s are also sold by salvage yards.
Parts sources: American Diesel Corp, Go2marine (Ford Lehman parts collection), Fred Warner Marine & Outdoors
Common problems (2)
-
Chronic oil leaks engine
Most 120s weep oil somewhere; owners often trace it to the rear of the engine near the heat exchanger (head/head gasket area) or to the drive seals of the gear-driven injection pump. Moderate oil use is treated as normal on these engines.trawlerforum.com · marineengine.com
-
Fuel leaks at injection pump, lift pump and return lines fuel
Slow diesel drips usually come from loose bleed screws or banjo washers, perished rubber injector return hoses, a failing lift-pump diaphragm, or worn internal seals in the Simms or CAV injection pump, which needs a pump shop to overhaul.yescenters.com
Maker’s service schedule (16)
| Engine oil & filter change | 200 hrs | “After first 15 hours running .... 1. Change Engine Oil ... Every 200 hours running ..... 17. Change engine and transmiss” — manufacturer (1986), marinedieselbasics.com |
| Fuel filters & water separator | 200 hrs | “Every 200 hours running ..... 18. Change all engine and fuel oil filters.” — manufacturer (1986), marinedieselbasics.com |
| Change oil in fuel injection pump | 50 hrs | “Every 50 hours running ...... 13. Check cleanliness of intake air filter. 14. Check (exchanger) zinc pencil. 15. Change” — manufacturer (1986), marinedieselbasics.com |
| Transmission fluid change | 200 hrs or 1 yr | “Change oil every 200 hours of operation or at least once each season under normal conditions” — manufacturer (1986), marinedieselbasics.com |
| Valve clearance check / adjust | 400 hrs | “After first 15 hours running .... 3. Adjust valve clearances. ... Every 400 hours running ..... 22. Adjust valve clearan” — manufacturer (1986), marinedieselbasics.com |
| Injector test / service | 400 hrs | “Every 400 hours running ..... 21. Remove and service injectors.” — manufacturer (1986), marinedieselbasics.com |
| Engine pencil zincs | 50 hrs | “After first 15 hours running .... 4. Check (exchanger) zinc pencil. ... Every 50 hours running ...... 14. Check (exchang” — manufacturer (1986), marinedieselbasics.com |
| Drive belts inspect / replace | 200 hrs | “After first 15 hours running .... 5. Adjust belt tension. ... Every 200 hours running ..... 16. Adjust belt tension.” — manufacturer (1986), marinedieselbasics.com |
| Air filter / intake silencer | 50 hrs | “After first 15 hours running .... 8. Check cleanliness of intake air filter. ... Every 50 hours running ...... 13. Check” — manufacturer (1986), marinedieselbasics.com |
| Clean fuel lift pump | 200 hrs | “Every 200 hours running ..... 19. Clean fuel lift pump.” — manufacturer (1986), marinedieselbasics.com |
| Clean injection pump cover filter | 200 hrs | “Every 200 hours running ..... 20. Clean injection pump cover filter.” — manufacturer (1986), marinedieselbasics.com |
| Remove raw water pump and check drive coupling | 400 hrs | “Every 400 hours running ..... 23. Remove raw water pump and check drive coupling. Place dab of grease on coupling halves” — manufacturer (1986), marinedieselbasics.com |
| Adjust idling speed (if required) | 400 hrs | “After first 15 hours running .... 10. Adjust idling speed (if required). ... Every 400 hours running ..... 24. Adjust id” — manufacturer (1986), marinedieselbasics.com |
| Check engine/propeller shaft alignment | 6 mo | “After first 15 hours running .... 9. Check engine/propeller shaft alignment. (twice annually, minimum).” — manufacturer (1986), marinedieselbasics.com |
| Replace Borg Warner transmission oil cooler | 1,200 hrs | “Suggested replacement is at 1200 hours.” — manufacturer, img1.wsimg.com |
| Inspect drive damper | 2,500 hrs | “Inspect your drive damper if you have more than 2500 hours on the engine.” — manufacturer, img1.wsimg.com |
Service part numbers (3)
| Raw-water impeller | Jabsco 1210-0001 | “6D380 5850-0001 040 3/4" NPT Flange SK33 3298 1210-0001” — manufacturer, marineengine.com · “Breakdown of 2C48 Pump ... 9 1 1210-0001 IMPELLER” — manufacturer, marinesurveyorontario.com |
| Raw-water pump kit original 2C45 pump (Jabsco 5850-0001) |
Jabsco SK33 | “6D380 5850-0001 040 3/4" NPT Flange SK33 3298 1210-0001” — manufacturer, marineengine.com |
| Raw-water pump kit Lehman 2C48 replacement pump (Jabsco 10950-2401 type) |
Jabsco SK239 | “Service Kit SK239 - Comprising Key 7/8/9/17” — manufacturer, marinesurveyorontario.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Ford Lehman 135 / SP135 (2725E) parts: good
Factory standard engine — you entered “Ford Lehman SP135”
Based on the later Ford 'Dover' 2725E 6.2 L naturally aspirated six (Ford built the Dover series 1982–1994, then Otosan/Dovertech to 2005). Parts are sold by the same Lehman specialists as the 120; American Diesel lists spare-parts sheets and Go2marine stocks cooling parts, heat exchangers and elbows for the 135. Do not assume 120 (2715E) and 135 (2725E) internals interchange.
Parts sources: American Diesel Corp, Go2marine (Ford Lehman parts collection)
Maker’s service schedule (14)
| Engine oil & filter change | 200 hrs | “Every 200 hours of operation ..... Change Engine Oil & Filter. And Transmission Oil.” — manufacturer (1987), marinedieselbasics.com |
| Fuel filters & water separator | 200 hrs or 1 yr | “should be replaced once each season or at least each 200 hours (which ever comes first) under normal conditions” — manufacturer (1987), marinedieselbasics.com |
| Raw-water pump impeller | 200 hrs | “Every 200 hours of operation ..... Replace raw water pump impeller.” — manufacturer (1987), marinedieselbasics.com |
| Coolant replacement & freeze-point test | 1,200 hrs | “Every 1200 hours of operation ..... Flush cooling system. Replace anti-freeze.” — manufacturer (1987), marinedieselbasics.com |
| Exhaust mixing elbow inspection | 200 hrs | “Every 200 hours of operation ..... Check exhaust components for leaks.” — manufacturer (1987), marinedieselbasics.com |
| Transmission fluid change Borg Warner gearbox | 200 hrs or 1 yr | “Change oil every 200 hours of operation or at least once each season under normal conditions” — manufacturer (1987), marinedieselbasics.com |
| Transmission fluid change PRM/Newage gearbox | 200 hrs | “After 25 hours running: Drain all oil from the gearbox and refill with one of the recommended lubricants.” — manufacturer (1987), marinedieselbasics.com |
| Transmission fluid change Twin Disc gearbox | 1,000 hrs or 6 mo | “The period between oil changes is 1000 hours of operation or 6 months, whichever occurs first.” — manufacturer (1987), marinedieselbasics.com |
| Check idling speed | 200 hrs | “Every 200 hours of operation ..... Check idling speed, adjust if required.” — manufacturer (1987), marinedieselbasics.com |
| Check coolant and oil hoses | 200 hrs | “Every 200 hours of operation ..... Check condition of all coolant and oil hoses.” — manufacturer (1987), marinedieselbasics.com |
| Check engine mount bolts | 200 hrs | “Every 200 hours of operation ..... Check all engine mount bolts.” — manufacturer (1987), marinedieselbasics.com |
| Replace thermostats | 3,600 hrs | “Every 3600 hours of operation ..... Replace thermostats.” — manufacturer (1987), marinedieselbasics.com |
| Replace Borg Warner transmission oil cooler Borg Warner gearbox | 1,200 hrs | “Suggested replacement time is at 1200 hours.” — manufacturer, img1.wsimg.com |
| Inspect drive damper | 2,500 hrs | “Inspect your drive damper if you have more than 2500 hours on the engine.” — manufacturer, img1.wsimg.com |
Service part numbers (9)
| Oil filter engines built before the 1987 change (original filter) |
Lehman 2N50 | “11 1 2N50 FILTER (Engine Oil Cooler Assembly D196/D197, SP90 / 135)” — manufacturer, marinesurveyorontario.com |
| Oil filter 1987-on engines (larger capacity, revised fitment) |
Lehman 2N53 | “DURING 1987 A NEW OIL FILTER OF LARGER CAPACITY ... THIS IS PART No. 2N53” — manufacturer, marinesurveyorontario.com · “Oil Filter 2N53 LM - P12-R105 P11-88” — dealer, lancingmarine.com |
| Fuel filter | Ford 6149717 × 2 | “2 ALL 2 6149717 FUEL FILTER ELEMENTS” — manufacturer, marinesurveyorontario.com |
| Raw-water impeller | Jabsco 1210-0001 | “Breakdown of 2C48 Pump ... 9 1 1210-0001 IMPELLER” — manufacturer, marinesurveyorontario.com |
| Raw-water pump kit | Jabsco SK239 | “Service Kit SK239 - Comprising Key 7/8/9/17” — manufacturer, marinesurveyorontario.com |
| Drive belt | Lehman 2B209 | “15 1 2B209 VBELT (Alternator Assembly D144, M/N)” — manufacturer, marinesurveyorontario.com · “Alternator Accessory Drive V-Belt 2B209 2B209 - P11-51” — dealer, lancingmarine.com |
| Air filter | Lehman 1F7 | “12 1 1F7 FOAM ELEMENT (Plenum Chamber / Air Filter Assembly D1125, SP135)” — manufacturer, marinesurveyorontario.com · “Air strainer to replace 2H75 & 1F7 (PF136) (Whilst stocks last)” — dealer, lancingmarine.com |
| Zinc / anode | Lehman EM21A | “25A 1 EM21A ZINC ANODE (Heat Exchanger Assembly D882/D883, SP135)” — manufacturer, marinesurveyorontario.com · “Anodes EM21A (Pack of 5) - - P11-18” — dealer, lancingmarine.com |
| Thermostat | Lehman 2C35 | “11 1 2C35 THERMOSTAT ... Modified / 12 1 1541317 GASKET” — manufacturer, marinesurveyorontario.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Caterpillar 3208 (NA / T / TA) parts: good
Factory optional engine — you entered “Caterpillar 3208N”
V8 introduced in the 1970s and discontinued in the late 1990s (Big Bear Engine gives 1999). Naturally aspirated versions run about 210 hp; turbo and turbo-aftercooled versions go up to 435 hp. Cat dealers still supply many genuine parts by serial number, and aftermarket in-frame/overhaul kits (pistons, rings, liners, bearings) are sold by Diesel Pro Power, Highway and Heavy Parts and others; complete remanufactured long blocks are also sold. The block is unsleeved from the factory but can be bored and sleeved during a rebuild.
Parts sources: Diesel Pro Power, Highway and Heavy Parts (Cat 3208), Big Bear Engine Company (3208 long blocks)
Common problems (3)
-
Aftercooler failure flooding the engine (TA models) cooling
The seawater-cooled aftercooler on turbo-aftercooled 3208s has aluminum parts that corrode; a failure can let seawater into the cylinders. Owners pull, clean, grease and pressure-test aftercoolers every 2–3 years and some replace them on a fixed schedule.trawlerforum.com · forums.ybw.com
-
Short life at high ratings / overloading engine
The higher-rated 3208TA engines last longer when run well below full power and propped so they can reach rated rpm; overheating or running at full load continuously shortens life.trawlerforum.com · trawlerforum.com
-
Overheating at high throttle cooling
Common causes owners check are clogged heat exchangers, thermostats, fouled keel coolers or restricted raw water flow, and faulty temperature senders.justanswer.com · facebook.com
Maker’s service schedule (20)
| Engine oil & filter change | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Engine Oil and Filter - Change” — manufacturer, princessklubben.se |
| Fuel filters & water separator | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Fuel System Primary Filter/Water Separator Element” — manufacturer, princessklubben.se |
| Raw-water pump impeller | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Auxiliary Water Pump - Inspect” — manufacturer, princessklubben.se |
| Engine pencil zincs | 50 hrs | “Every 1900 L (500 US gal) of Fuel or 50 Service Hours ... Zinc Rods - Inspect/Replace” — manufacturer, princessklubben.se |
| Air filter / intake silencer | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Engine Air Cleaner Element - Clean/Replace” — manufacturer, princessklubben.se |
| Valve clearance check / adjust | 2,000 hrs | “Initial 9000 L (2400 US gal) of Fuel or 250 Service Hours or 1 Year ... Engine Valve Lash - Inspect/Adjust” — manufacturer, princessklubben.se |
| Coolant replacement & freeze-point test Cat DEAC / conventional coolant | 1,000 hrs or 2 yrs | “Every 36 000 L (9000 US gal) of Fuel or 1000 Service Hours or 2 Years ... Cooling System Coolant (DEAC) - Change” — manufacturer, princessklubben.se |
| Coolant replacement & freeze-point test Cat ELC (extended life coolant) | 6,000 hrs or 4 yrs | “Every 216 000 L (57 000 US gal) of Fuel or 6000 Service Hours or 4 Years ... Cooling System Coolant (ELC) - Change” — manufacturer, princessklubben.se |
| Turbocharger inspection | 1,000 hrs or 2 yrs | “Every 36 000 L (9000 US gal) of Fuel or 1000 Service Hours or 2 Years ... Aftercooler Core - Clean/Test” — manufacturer, princessklubben.se |
| Turbocharger inspect | 2,000 hrs | “Every 72 000 L (19 000 US gal) of Fuel or 2000 Service Hours ... Turbocharger - Inspect” — manufacturer, princessklubben.se |
| Heat exchanger & oil cooler cleaning | 2,000 hrs | “Every 72 000 L (19 000 US gal) of Fuel or 2000 Service Hours ... Heat Exchanger - Inspect” — manufacturer, princessklubben.se |
| Injector test / service | 2,000 hrs | “Every 72 000 L (19 000 US gal) of Fuel or 2000 Service Hours ... Fuel Injection Nozzles - Test/Exchange” — manufacturer, princessklubben.se |
| Sea water strainer clean/inspect | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Sea Water Strainer - Clean/Inspect” — manufacturer, princessklubben.se |
| Coolant SCA test/add | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Cooling System Supplemental Coolant Additive (SCA)” — manufacturer, princessklubben.se |
| Hoses and clamps inspect/replace | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Hoses and Clamps - Inspect/Replace” — manufacturer, princessklubben.se |
| Crankcase breather clean | 250 hrs or 1 yr | “Every 9000 L (2400 US gal) of Fuel or 250 Service Hours or Yearly ... Engine Crankcase Breather - Clean” — manufacturer, princessklubben.se |
| Thermostat (water temperature regulator) replace | 1,000 hrs or 2 yrs | “Every 36 000 L (9000 US gal) of Fuel or 1000 Service Hours or 2 Years ... Cooling System Water Temperature Regulator - R” — manufacturer, princessklubben.se |
| Marine transmission oil cooler clean/inspect | 1,000 hrs or 2 yrs | “Every 36 000 L (9000 US gal) of Fuel or 1000 Service Hours or 2 Years ... Marine Transmission Oil Cooler - Clean/Inspect” — manufacturer, princessklubben.se |
| Crankshaft vibration damper inspect | 2,000 hrs | “Every 72 000 L (19 000 US gal) of Fuel or 2000 Service Hours ... Crankshaft Vibration Damper - Inspect” — manufacturer, princessklubben.se |
| Jacket water pump inspect | 3,000 hrs or 2 yrs | “Every 108 000 L (28 500 US gal) of Fuel or 3000 Service Hours or 2 Years ... Water Pump - Inspect” — manufacturer, princessklubben.se |
Service part numbers (4)
| Fuel filter | Caterpillar 1R-0750 | “| Fuel Filter | 1R0750 |” — dealer, marineenergy.com.au · “Fuel Filter for Caterpillar 3208 Natural and Turbo engines 1R0750 Advanced Efficiency” — dealer, dieselpro.com |
| Zinc / anode heat-exchanger anode (10 mm); 2 on the 4W-9164 heat exchanger, 3 on the 7C-3114 heat exchanger |
Caterpillar 6L-2283 | “| Anodes on 7C-3114 Heat Exchanger | 6L-2283 | [CM6L2283] x 3.” — dealer, marineenergy.com.au · “Zinc Anode for Caterpillar Marine Engines 6L2283 NPT: 1/4”” — dealer, dieselpro.com |
| Zinc / anode 16 mm anode, starboard bottom of bonnet, 4W-9164 heat exchanger only |
Caterpillar 6L-2289 | “Anodes on 4W-9164 Heat Exchanger | 6L-2283 6L-2289 ... [TEC 02023] x 1. Starboard Side, bottom of the bonnet. 16mm” — dealer, marineenergy.com.au · “Zinc Anode for Caterpillar Marine Engines 6L2289 NPT: 1/2”” — dealer, dieselpro.com |
| Zinc / anode transmission oil cooler anode (if the cooler has one) |
Caterpillar 6L-2288 | “| Anode - Transmission Oil Cooler (If present on cooler) | 6L-2288 |” — dealer, marineenergy.com.au · “Zinc Anode for Caterpillar Marine Engines 6L2288 NPT: 1/2”” — dealer, dieselpro.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Sources disagree on horsepower — left blank rather than guessed.
Cummins 6BT / 6BTA 5.9 parts: good
Factory optional engine — you entered “Cummins 6BT5.9”
Mechanically injected 5.9 L inline six from the Cummins B-series truck/industrial family, so base-engine parts are everywhere. Cummins still sells factory ReCon (remanufactured) marine 6BT/6BTA engines (152–210 hp ratings) with a 2-year/2000-hour warranty. Seaboard Marine is the best-known marine specialist, selling aftercooler/heat-exchanger service kits, upgraded raw water pumps and technical guidance; TAD also sells Cummins packages.
Parts sources: Seaboard Marine, Cummins (ReCon 6BT/6BTA), Diesel Pro Power
Common problems (2)
-
Aftercooler corrosion letting seawater into the intake cooling
On the turbo-aftercooled 6BTA the seawater-cooled aftercooler core has vertical tubes and an aluminum housing that corrodes from condensate; a leak can put salt water into the cylinders and wreck the engine. Owners pull, clean, grease and pressure-test the core every few years and fit new O-rings.trawlerforum.com · sbmar.com
-
Heat exchanger and aftercooler service cooling
Routine seawater-side service (O-rings, gaskets, zincs) is a recurring owner job; kits are sold for it and refilling coolant without trapping air is a common question.sbmar.com · sbmar.com
Service part numbers (5)
| Oil filter | Cummins 3937743 | “| Oil Filter | 3937743 |” — dealer, marineenergy.com.au · “Cummins Oil Filter 3937743 Spin-on type, 3.66" outside diameter, 6.95" height” — dealer, dieselpro.com |
| Fuel filter 6BT 5.9 210 hp (CPL 742) |
Fleetguard FF5052 Replaces FF42000, FS1251 |
“on-engine fuel filter with drain for all 6BT 210 B’s (CPL 742). Replaces the FF42000, FS1251.” — dealer, sbmar.com · “Cummins 6BT Fuel Filter 3931063 FF5052” — dealer, marineenergy.com.au |
| Fuel filter late 6BTA (also late 4BTA and 6CTA) |
Fleetguard FF5285 | “Fleetguard FF5285 Fuel Filter – late 4BTA 6BTA and 6CTA’s” — dealer, sbmar.com · “Cummins 6BTA Fuel Filter 3890017 FF5285 ... suits late model Cummins 6BTA's, 6CTA8.3-M” — dealer, marineenergy.com.au |
| Raw-water impeller seawater pump with 1-1/4 in hose ports (Sherwood M70/M71 type, early 4BT/6BT) |
Sherwood 10615K | “Seawater Pump Impeller | **1-1/4" PORTS** 3908220 10615K” — dealer, marineenergy.com.au · “Cummins Marine Water Pump Impeller 10615K 2 9/16" diameter, 1 5/8" length” — dealer, dieselpro.com |
| Raw-water impeller keyway-shaft pump, 2 in inlet / 1-3/4 in outlet, 11° offset flange (e.g. P1716/P1730 on 6BTA) |
Sherwood 17000K | “**2" inlet & 1-3/4" outlet ports with 11° OFFSET flange** 17000K” — dealer, marineenergy.com.au · “Cummins Impeller for Key Shaft 17000K” — dealer, dieselpro.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Model sources (15)
hmy.com · trawlerforum.com · oxfordyachtagency.com · grandbanks.com · trawlerforum.com · denisonyachtsales.com · curtisstokes.net · curtisstokes.net · curtisstokes.net · denisonyachtsales.com · grandyachts.com · breweryacht.com · murrayyachtsales.com · oxfordyachtagency.com · denisonyachtsales.com
Other Grand Banks models
- Grand Banks 32 Sedan
- Grand Banks 42 Classic 1975–2005
- Grand Banks 46 Classic 1987–2004
- Grand Banks 49 Classic 1980–1999
Researched from public sources. Spotted an error? The sources are listed above — tell us what they got wrong.