Vessel Guide

Models › Sea Ray

Sea Ray 370 Sedan Bridge

Built 1991–1997 by Sea Ray Boats

Is she right for you? Take the quiz Own one? Start her custom manual Looking at one? Sea-trial scorecard

About the Sea Ray 370 Sedan Bridge

Researched from public sources for this model. Any individual boat may have been modified or repowered — confirm before relying on any figure.

Illustration of a Sea Ray 370 Sedan Bridge
Illustration, not a photo of this model. AI-generated illustration of a typical flybridge motor yacht.
Built
1991–1997
Builder
Sea Ray Boats
Length
40.83 ft
Beam
12.33 ft
Draft
2.58 ft
Displacement
14,600 lb
Hull
fiberglass
Hull / keel
planing
Propulsion
inboard
Fuel
250 gal
Water
70 gal
Holding
20 gal
Stern thruster
not fitted
Tank capacities — where the figures come from
  • Fuel 250 gal
    “250 US Gallons / 946 Litres” — spec database (1992), everythingsearay.com · “250 gallons (2 tanks)” — search excerpt (1995), kentmorrmarina.net
    An enthusiast archive of factory specs and several listings agree; no builder document was checked. One listing says the fuel is in two tanks.
  • Water 70 gal
    “70 US Gallons / 264 Litres” — spec database (1992), everythingsearay.com · “70 gallons of water” — search excerpt (1996), boattrader.com
    Non-builder sources agree; no builder figure could be checked.
  • Holding 20 gal
    “Holding Tank Capacity: 20 gallons” — search excerpt (1995), kentmorrmarina.net · “a 20-gallon holding tank” — search excerpt (1996), boattrader.com · “1 tank (s), capacity 20 gallons” — search excerpt (1996), deltamarinesales.com
    Only listings give this, and they likely share one spec database. 20 gal is small for a 40-ft boat, but nothing contradicts it.
  • Water heater unknown
    No builder spec sheet for 1991-97 was found; spec databases only list a water heater, without a size.

Tanks are often replaced or added on older boats — check the tank labels or a survey for yours.

Thrusters and steering — where this comes from
  • Bow thruster unknown
    No builder spec sheet or option list for 1991-97 was found. A later sister model from the 380/400 era offered bow thrusters as an option, but that doesn't carry over.
  • Stern thruster not fitted
    Our earlier figure of none has no source, and nothing was found either way.
  • Steering unknown
    A buyer's-guide summary mentions a tilt steering wheel and an optional lower helm but not the steering system.

Thrusters and steering are often replaced — check the units on your boat before ordering parts.

Sources disagree on engines[MerCruiser].hp, hp (standard gas engines) — left blank rather than guessed.

Solid fiberglass deep-V (21 deg) with prop pockets and side exhausts. Hull length 36.8 ft; LOA includes platform. Lower helm optional. Narrow side decks.

Engines fitted

Boats of the same model can differ — check which engines yours actually has before ordering parts.

Generator

“Standard: 7.5 kW (120V/60 Cycles) Quicksilver Gas Generator; Optional: 9.0 kW Westerbeke Gas, 8.0 kW Quicksilver Diesel,” — spec database (1992), everythingsearay.com · “7.5 Kw Quicksilver generator for 110v power away from the dock” — broker listing (1992), powerboatlistings.com

An enthusiast Sea Ray database copying 1992 factory specs lists a 7.5 kW Quicksilver gas generator as standard, with a 9.0 kW Westerbeke gas or 8.0 kW Quicksilver or Westerbeke diesel as options, and a 1992 listing shows the 7.5 kW Quicksilver. No builder document or review confirms this, so we list no set.

Manuals and brochures online

Hosted by the builder or an owners' association; they own the copyright.

Known problems for this model

No well-sourced problem reports found yet.

Engines & parts

MerCruiser 7.4 (454) V8 gas parts: good

Factory standard engine — you entered “MerCruiser 7.4L V8 inboard (454)”

GM big-block base; Marine Engine Depot and others sell 7.4 L engines and parts, and cast-iron riser kits run a few hundred dollars. Manifold and riser replacement is the main recurring expense.

Parts sources: Marine Engine Depot, Power Boat Supply

Common problems (2)
  • Manifold and riser corrosion exhaust
    As with other gas marine V8s, internally rusted manifolds and risers can let water into the engine; periodic replacement is standard practice.
    powerandmotoryacht.com
  • Rough running and won't rev under load fuel
    Common troubleshooting threads trace this to fuel delivery (filters, pump, carburetor) or ignition timing problems.
    justanswer.com · youtube.com
Maker’s service schedule (8)
Engine oil & filter change100 hrs or 1 yr
“Most four-stroke outboards and sterndrive engines require an oil change either annually or every 100 hours of operation.” — manufacturer, mercurymarine.com
Fuel filters & water separator100 hrs or 1 yr
“The fuel filter on your engine should be inspected or replaced per the maintenance schedule in your owner's manual, usua” — manufacturer, mercurymarine.com
Raw-water pump impeller300 hrs or 3 yrs
“How often should my seawater pump impeller be serviced? Every 300 hours or 3 years, whichever comes first.” — manufacturer, mercurymarine.com
Spark plugs inspect / replace300 hrs or 3 yrs
“How often should spark plugs be changed? Every 300 hours or 3 years, whichever comes first.” — manufacturer, mercurymarine.com
Coolant replacement & freeze-point test
closed (freshwater) cooling only
5 yrs
“How often should coolant be changed on engines with closed cooling? Every 5 years.” — manufacturer, mercurymarine.com
Transmission fluid change
sterndrive gear lube
1 yr
“Gearcase lubricant in outboard and sterndrive lower units should also be changed annually or at the service interval spe” — manufacturer, mercurymarine.com
Lubricate steering linkage and check power-steering fluid
sterndrive
100 hrs or 1 yr
“Mercury Marine recommends lubricating the steering linkage and checking the power steering fluid level in ... MerCruiser” — manufacturer, mercurymarine.com
Check power trim fluid level
sterndrive
100 hrs or 1 yr
“Power trim and tilt fluid level should be checked annually or every 100 hours.” — manufacturer, mercurymarine.com
Service part numbers (4)
Oil filter Mercury Quicksilver 35-866340Q03
“Part number: 866340Q03 ... for MerCruiser sterndrive and inboard engines except V6 engines with the oil filter mounted o” — manufacturer, mercurymarine.com · “14957 FILTER, Oil (1 required per assembly) ... 35-866340Q03 - Oil Filter” — dealer, marineengine.com
Fuel filter
carbureted engines (Rochester 4-barrel): filter inside carburetor fuel inlet
Mercury 53336T
“For use on MerCruiser 3.0L, 4.3L, 5.0L , 5.7L and 7.4L engines with Rochester 2- and 4-barrel and MerCarb” — manufacturer, mercurymarine.com
Raw-water impeller
Bravo sterndrive / inboard with pre-2000 engine-mounted plastic sea water pump
Mercury Quicksilver 47-59362Q01
Also: Sierra 18-3087
“For MerCruiser engines with engine mounted, 2-piece, plastic sea water pumps.” — manufacturer, mercurymarine.com · “Included water Pump Impeller 59362Q01 fits Pre-2000 plastic seawater sea pumps. WILL NOT work on newer (2000+)” — dealer, midnightmarine.net
Thermostat
standard cooling, 160 F
Mercury Quicksilver 807252Q5
“Thermostat 807252Q5 is for V6 and V8 MerCruiser engines ... made by General Motors (model year 1987-2016)” — manufacturer, mercurymarine.com

From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.

Caterpillar 3116 parts: limited

Factory optional engine — you entered “Caterpillar 3116 TA”

Supported by Cat dealers by serial number; aftermarket rebuilders (e.g., Big Bear Engine) sell parts and address known problems. Some 3116s built in France ('soft block') were problematic and owners are told to check serial numbers with Cat.

Parts sources: Big Bear Engine Company, Diesel Pro Power

Common problems (4)
  • Failures in high-load use engine
    3116s generally do fine in trawlers but problems show up in fast boats run near full power for long periods; poor propping that overloads the engine ages it quickly.
    trawlerforum.com
  • 'Soft block' engines engine
    A batch of French-built blocks had a reputation for early failure, sometimes within a few hundred hours.
    trawlerforum.com
  • Injectors, fuel rack and heads fuel
    Owners and rebuilders report injector/injector-cup, fuel rack and cylinder head problems; good maintenance history matters when buying.
    4btengines.com · facebook.com
  • Low turbo/exhaust mixer height exhaust
    The low-mounted turbo and exhaust mixer make it harder to get adequate exhaust riser height, so the exhaust installation needs care to avoid water backflow.
    trawlerforum.com
Maker’s service schedule (18)
Engine oil & filter change250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Engine Oil and Filter - Change” — manufacturer, oxfordyachtagency.com
Fuel filters & water separator250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Fuel System Primary Filter/Water Separator Element” — manufacturer, oxfordyachtagency.com
Raw-water pump impeller250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Auxiliary Water Pump - Inspect” — manufacturer, oxfordyachtagency.com
Engine pencil zincs50 hrs
“Every 1500 L (400 US gal) of Fuel or 50 Service Hours ... Zinc Rods - Inspect/Replace” — manufacturer, oxfordyachtagency.com
Valve clearance check / adjust2,000 hrs
“First 7500 L (2000 US gal) of Fuel or 250 Service Hours ... Engine Valve Lash - Inspect/Adjust” — manufacturer, oxfordyachtagency.com
Coolant replacement & freeze-point test
Cat DEAC / conventional coolant
1,000 hrs or 2 yrs
“Every 30 000 L (8000 US gal) of Fuel or 1000 Service Hours or 2 Years ... Cooling System Coolant (DEAC) - Change” — manufacturer, oxfordyachtagency.com
Coolant replacement & freeze-point test
Cat ELC (extended life coolant)
6,000 hrs or 4 yrs
“Every 182 000 L (48 000 US gal) of Fuel or 6000 Service Hours or 4 Years ... Cooling System Coolant (ELC) - Change” — manufacturer, oxfordyachtagency.com
Turbocharger inspection1,000 hrs or 2 yrs
“Every 30 000 L (8000 US gal) of Fuel or 1000 Service Hours or 2 Years ... Aftercooler Core - Clean/Test” — manufacturer, oxfordyachtagency.com
Turbocharger inspect1,000 hrs or 2 yrs
“Every 30 000 L (8000 US gal) of Fuel or 1000 Service Hours or 2 Years ... Turbocharger - Inspect” — manufacturer, oxfordyachtagency.com
Heat exchanger & oil cooler cleaning2,000 hrs
“Every 60 000 L (16 000 US gal) of Fuel or 2000 Service Hours ... Heat Exchanger - Inspect” — manufacturer, oxfordyachtagency.com
Drive belts inspect / replace250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Belt - Inspect” — manufacturer, oxfordyachtagency.com
Fuel injection timing check2,000 hrs
“First 7500 L (2000 US gal) of Fuel or 250 Service Hours ... Fuel Injection Timing - Check” — manufacturer, oxfordyachtagency.com
Thermostat (coolant temperature regulator) replace3,000 hrs or 2 yrs
“Every 91 000 L (24 000 US gal) of Fuel or 3000 Service Hours or 2 Years ... Cooling System Water Temperature Regulator -” — manufacturer, oxfordyachtagency.com
Sea water strainer clean/inspect250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Sea Water Strainer - Clean/Inspect” — manufacturer, oxfordyachtagency.com
Jacket water pump inspect250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Water Pump - Inspect” — manufacturer, oxfordyachtagency.com
Coolant SCA test/add250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Cooling System Supplemental Coolant Additive (SCA)” — manufacturer, oxfordyachtagency.com
Hoses and clamps inspect/replace250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Hoses and Clamps - Inspect/Replace” — manufacturer, oxfordyachtagency.com
Crankcase breather clean250 hrs or 1 yr
“Every 7500 L (2000 US gal) of Fuel or 250 Service Hours or 1 Year ... Engine Crankcase Breather - Clean” — manufacturer, oxfordyachtagency.com
Service part numbers (3)
Oil filter Sources disagree: 1R-0658 / 324-2598
“**Oil Filter** **CAT 1R-0658** | 3126B C7 3306 3304 3116 C4.2 3046 3066” — dealer, marineenergy.com.au · “Caterpillar 324-2598 Advanced Efficiency 3116 and 3126 Diesel Engine Oil Filter” — dealer, marineengineparts.com
Fuel filter Caterpillar 1R-0751
Also: Baldwin BF7632, Fleetguard FF5324, WIX 33626
“Caterpillar 1R-0751 Advanced Efficiency 3116 and 3126 Diesel Engine Fuel Filter” — dealer, marineengineparts.com · “the secondary fuel filter Cat specifies for the 3114, 3116, 3126/B/E, C7, and C9 family” — dealer, allprodiesel.net
Raw-water impeller
keyway-shaft Sherwood seawater pump
Sherwood 17000K
“| **Impeller** | 17000K KEY WAY |” — dealer, marineenergy.com.au · “Caterpillar Marine Engines ... Common applications include: ... CAT 3116” — dealer, marisolmarine.com
Zinc / anode Caterpillar 6L-2283 × 3
“**Anode kit CAT3116** | 3 x 6L2283 2 x 6L2281 1 x 6L3104” — dealer, marineenergy.com.au · “Zinc Anode for Caterpillar Marine Engines 6L2283 NPT: 1/4”” — dealer, dieselpro.com

From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.

Model sources (6)

hmy.com · everett.boatshed.com · powerboatlistings.com · boats-from-usa.com · everythingsearay.com · powerboatlistings.com

Other Sea Ray models

Researched from public sources. Spotted an error? The sources are listed above — tell us what they got wrong.