Silverton 37 Convertible (1980-89)
Built 1980–1989 by Silverton Marine
About the Silverton 37 Convertible (1980-89)
Researched from public sources for this model. Any individual boat may have been modified or repowered — confirm before relying on any figure.
- Built
- 1980–1989
- Builder
- Silverton Marine
- Length
- 37 ft
- Beam
- 14 ft
- Draft
- 3.58 ft
- Displacement
- 20,000 lb
- Hull / keel
- planing
- Propulsion
- inboard
- Fuel
- 300 gal
- Water
- 100 gal
- Water heater
- AC
- Stern thruster
- not fitted
- Steering
- hydraulic
Tank capacities — where the figures come from
-
Fuel 300 gal
“Fuel Tank Capacity (gal): 300 gallons” — search excerpt (1985), marinesource.comListings agree; no builder figure.
-
Water 100 gal
“Water Tank Capacity (gal): 100 gallons” — search excerpt (1985), marinesource.comListings agree; no builder figure.
-
Holding unknown
“a 40-gallon holding” — search excerpt (1985), boattrader.comOne listing only (1985 boat).
-
Water heater AC
“Check with your Silverton dealer for the capacity of the water heater installed on your yacht. The water heater operates” — owner's manual (1986-1999 (all models)), silvertonclub.comOnly Silverton's general 1986-1999 owner's manual was found (it covers the 1986-89 boats but isn't model-specific): a 120 V water heater with a heat exchanger that may be connected to the engines, capacity left to the dealer.
Tanks are often replaced or added on older boats — check the tank labels or a survey for yours.
Thrusters and steering — where this comes from
-
Bow thruster unknown
The builder's general owner's manual (1986-99) does not mention a thruster; no option list found.
-
Stern thruster not fitted
Our earlier figure of none has no source; the Silverton general owner's manual (1986-99) never mentions a thruster.
-
Steering hydraulic
“Your Silverton yacht has a modern, manual, hydraulic steering system. The system consists of the "head" pump at the helm” — owner's manual (1986-1999), silvertonclub.comSilverton's general owner's manual covers 1986-99 models, so it confirms manual hydraulic steering for 1986-89 boats only; 1980-85 boats are not documented in any source found.
Thrusters and steering are often replaced — check the units on your boat before ordering parts.
Single-stateroom layout with full dinette. V-drive installation on the earliest boats, switched to straight inboards in 1981. Teak interior before 1985, oak after. Most have 350hp Crusader gas engines (18-19 kt cruise).
Engines fitted
-
Crusader 454 cid V8 (350 hp) — 350 hp, gas, twin
standard
HMY: most 37s have twin 350 hp Crusader gas engines. A 1989 boat lists twin Crusaders rated 350 hp and describes them as 454s.Sources: hmy.com · seattleyachts.com
-
Perkins — 200 hp, diesel, twin
standard
HMY: twin 200 hp Perkins diesels were standard on early models; Perkins model not named.Sources: hmy.com
Boats of the same model can differ — check which engines yours actually has before ordering parts.
Generator
The general manual says a generator is optional or unavailable depending on model, without naming models. No model-specific source found.
Manuals and brochures online
- Owner's manual Silverton general owner's manual for models 1986-1999 (1986-1999) — silvertonclub.com
Hosted by the builder or an owners' association; they own the copyright.
Known problems for this model
No well-sourced problem reports found yet.
Engines & parts
Crusader 350 / 454 inboard gas V8 parts: good
Factory standard engine — you entered “Crusader 454 cid V8 (350 hp)”
GM-based inboard engines; Crusader (now part of Pleasurecraft Marine Engine Co.) still publishes illustrated parts manuals and sells through distributors. Go2marine stocks Crusader manifolds, risers, raw water pumps and ignition parts; Osco and Barr make aftermarket manifolds, and new GM/Crusader base engines are sold by rebuilders.
Parts sources: Crusader Engines, Go2marine (Crusader parts), 1-800-RUNS-NEW (GM & Crusader base engines)
Common problems (1)
-
Clogged or failing manifolds/risers exhaust
Owners find individual risers running much hotter than the others (a sign of internal blockage) and debate replacing vs. flushing; Osco manifolds are often preferred as closest to OEM.marineengine.com · marineengine.com
Maker’s service schedule (14)
| Engine oil & filter change 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 50 hrs or 1 yr | “Change engine oil and filter — After 1st 25 Hrs / Every 50 Hours of Operation / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Fuel filters & water separator 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 50 hrs or 1 yr | “Fuel Filters - Service or replace — After 1st 25 Hrs / Every 50 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Raw-water pump impeller 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Cooling System - Inspect/Replace raw water pump impeller — Every 100 Hours of Operation / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Drive belts inspect / replace 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Drive Belt - Inspect condition and check tension — After 1st 25 Hrs / Every 100 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Spark plugs inspect / replace 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Ignition System and Spark Plugs - Clean and inspect condition — After 1st 25 Hrs / Every 100 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Exhaust mixing elbow inspection 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 4 mo | “Exhaust System - Check condition and tightness of all hose clamps — After 1st 25 Hrs / Every 100 Hours(1) / Once Each Ye” — manufacturer (2013), crusaderengines.com |
| Coolant replacement & freeze-point test 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 5 yrs | “Fresh-water cooled models - Change coolant — Every five years” — manufacturer (2013), crusaderengines.com |
| Engine pencil zincs 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 1 mo | “Zinc Anodes - Heat exchanger and cooler - check condition — Every 30 days” — manufacturer (2013), crusaderengines.com |
| Transmission fluid change 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 1 yr | “Transmission and "V" Drive - Change fluid and clean strainer, if equipped — After 1st 25 Hrs (Hurth Only) / Once Each Ye” — manufacturer (2013), crusaderengines.com |
| Flame arrestor & crankcase ventilation - clean and inspect 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Flame Arrestor and Crankcase Ventilation System - Clean and inspect — Every 100 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Engine alignment check 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 1 yr | “Engine Alignment - Check and adjust if necessary — After 1st 25 Hrs / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Inspect all hoses (and cooling hose clamps) 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Hoses (all) - Inspect for cracks, swelling, weather checking or other signs of deterioration — Every 100 Hours / Once Ea” — manufacturer (2013), crusaderengines.com |
| Shift & throttle cable linkage - inspect and lubricate 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 4 mo | “Shift and Throttle Cable Linkage - Inspect and lubricate — Every 100 Hours(1) / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Electrical system - check connections and wiring 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 50 hrs or 2 mo | “Electrical System (complete) - Check for loose or dirty connections and damaged wiring — Every 50 Hours(2) / Once Each Y” — manufacturer (2013), crusaderengines.com |
Service part numbers (18)
| Oil filter remote-mounted oil filter (MP7.4L and 2013 5.0/5.7/6.0L MPI) |
Crusader 22679 | “Oil Filter 22679 (MAINTENANCE ITEM PART NUMBERS)” — manufacturer, crusaderengines.com |
| Fuel filter MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008 |
Crusader 47038 | “Fuel Filter 47038 (MAINTENANCE ITEM PART NUMBERS)” — manufacturer, crusaderengines.com |
| Fuel filter 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13 |
Crusader RP080026 | “Fuel Control Cell (FCC) Fuel Filter Element RP080026” — manufacturer, crusaderengines.com |
| Fuel pre-filter / separator MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: engine-mounted Racor water-separating filter 47046 |
Crusader 47047 | “25 47047 Element, Racor fuel filter (Not Shown) 1” — manufacturer, crusaderengines.com |
| Fuel pre-filter / separator 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13: primary fuel filter |
Crusader R080033 | “Primary Fuel Filter Element R080033” — manufacturer, crusaderengines.com |
| Raw-water impeller MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008 (raw water pump RA057031) |
Crusader RP061017 Replaces R061017 |
“Replaces Crusader R061017 (Impeller Kit with Gasket & O-Ring | Crusader RP061017)” — dealer, marinepartssource.com · “Replaces Crusader R061017 (Impeller Kit with Gasket & O-Ring | Crusader RP061017)” — dealer, marinesuppliesdepot.com |
| Raw-water impeller 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13 |
Crusader RP061022 | “Impeller , Raw Water Pump (1) RP061022 (ON-BOARD PARTS KIT 5.7L)” — manufacturer, crusaderengines.com |
| Raw-water pump kit MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008 (raw water pump RA057031) |
Crusader 40064 | “40064 Overhaul Kit, Major (includes items 2, 3, 11, 14 and 15)” — manufacturer, crusaderengines.com |
| Drive belt MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: alternator drive |
Crusader 98210 | “Alternator Drive Belt 98210” — manufacturer, crusaderengines.com |
| Drive belt MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: raw water pump drive |
Crusader 10258 | “Raw Water Pump Drive Belt 10258” — manufacturer, crusaderengines.com |
| Drive belt 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13, left-hand (LH) rotation: serpentine |
Crusader R066028 | “Belt , Serpentine (1) R066028 (ON-BOARD PARTS KIT 5.7L (LH))” — manufacturer, crusaderengines.com |
| Drive belt 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13, right-hand (RH) rotation: serpentine |
Crusader R066029A | “Belt , Serpentine (1) R066029A (ON-BOARD PARTS KIT 5.7L (RH))” — manufacturer, crusaderengines.com |
| Spark plug MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: platinum plug |
Crusader 49078 × 8 | “Spark Plugs (platinum) 49078” — manufacturer, crusaderengines.com |
| Spark plug 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13: platinum plug set |
Crusader RP030010 | “Spark Plug , Set, (Platinum) (1) RP030010 (ON-BOARD PARTS KIT 5.7L)” — manufacturer, crusaderengines.com |
| Thermostat MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: raw-water (standard) cooling, 143 F |
Crusader R026002E | “6 R026002E Thermostat (143-degree) 1 (Raw Water Cooling Components - Figure 18)” — manufacturer, crusaderengines.com |
| Thermostat MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: fresh-water (closed) cooling kit, 170 F |
Crusader 98203 | “5 98203 Thermostat (170-degree) 1 (Fresh Water Cooling Components 1)” — manufacturer, crusaderengines.com |
| Zinc / anode MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: oil cooler / transmission cooler / heat exchanger |
Crusader R168005 | “24 R168005 Zinc, sacrificial 1 (Raw Water Cooling Components - Figure 18)” — manufacturer, crusaderengines.com |
| On-board spare parts kit (belt, cap, rotor, fuses, relays, plugs, impeller, fuel filters) 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13, LH rotation |
Crusader RK173089D-07 | “ON-BOARD PARTS KIT 5.7L (LH) 2007 TO PRESENT, FCC FUEL SYSTEM RK173089D-07” — manufacturer, crusaderengines.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Model sources (3)
Other Silverton models
- Silverton 34 Convertible (1991-95) 1991–1995
- Silverton 402 / 422 Motor Yacht 1996–2001
Researched from public sources. Spotted an error? The sources are listed above — tell us what they got wrong.