Trojan 36 Convertible
Built 1972–1989 by Trojan Yachts
Is she right for you? Take the quiz
Own one? Start her custom manual
Looking at one? Sea-trial scorecard
About the Trojan 36 Convertible
Researched from public sources for this model. Any individual boat may have been modified or repowered — confirm before relying on any figure.
- Built
- 1972–1989
- Builder
- Trojan Yachts
- Length
- 36 ft
- Beam
- 13 ft
- Draft
- 2.92 ft
- Displacement
- 16,000 lb
- Hull
- fiberglass
- Hull / keel
- planing
- Propulsion
- inboard
- Generator
- fitted on some boats
- Bow thruster
- not fitted
- Stern thruster
- not fitted
Tank capacities — where the figures come from
-
Fuel unknown
“Fuel: 350g (twin 125g saddle tanks, twin 50 gallon aft aux tanks)” — search excerpt (1987), mapleleafyachtsales.com · “Fuel Tank Capacity (gal): 250 gallons” — search excerpt (1978), marinesource.com · “Fuel Capacity 240 gal” — search excerpt (1977), seacoastyachts.comListings suggest two 125-gal saddle tanks (250 gal) plus two 50-gal aft auxiliary tanks bringing it to 350; the auxiliary tanks may have been optional, or standard later. Our earlier 350 matches only the 1987 boat. No builder figure was found.
-
Water unknown
“Water: 100g” — search excerpt (1987), mapleleafyachtsales.com · “Water Capacity 90 gal” — search excerpt (1977), seacoastyachts.com · “Water Tank Capacity (gal): 30 gallons” — search excerpt (1978), marinesource.comListings give 30, 90 and 100 gal; our earlier 80 came from a spec database. Nothing settles it.
-
Holding unknown
“Holding: 75g” — search excerpt (1987), mapleleafyachtsales.comOne listing (a 1987 boat) gives this, and a private-sale ad for another 1987 boat also says about 75 gal.
-
Water heater unknown
“Water Heater - 25g” — broker listing (1987), mapleleafyachtsales.comOne 1987 F-36 for sale; no builder or review figure found.
Tanks are often replaced or added on older boats — check the tank labels or a survey for yours.
Thrusters and steering — where this comes from
-
Bow thruster not fitted
No source mentions a thruster either way, so our earlier figure of none has no source behind it.
-
Stern thruster not fitted
Nothing was found either way; our earlier figure of none has no source.
-
Steering unknown
Nothing F-36-specific was found. The Trojan owners' site shows the F-series used both chain-and-gear mechanical steering (1973 F-32 test) and dual-station hydraulic (a 1978 F-28 owner says the manuals call for it), so the F-36 may have changed during its 1972-89 run too; not confirmed.
Thrusters and steering are often replaced — check the units on your boat before ordering parts.
Sources disagree on fuel tank, water tank — left blank rather than guessed.
Fiberglass hull with nearly flat (9 deg) aftersections and shallow keel. One- or two-stateroom layouts; lower helm popular option. Various gas and diesel engines offered; fuel 250 or 350 gal.
Engines fitted
-
Crusader 350 hp gas V8 inboard — 350 hp, gas, twin
standard
HMY: many gas and diesel options were offered over the years; among the most popular, twin 350 hp Crusaders cruise about 19 kn (mid-high 20s top). HMY does not say which package was the base engine.Sources: hmy.com
-
Chrysler 440 gas V8 — 330 hp, gas, twin
standard
Soundings (2019, archived) profiles a 1975 Trojan F-36 Convertible that came with a pair of Chrysler 440 gas engines of about 330 hp each.Sources: web.archive.org
-
MerCruiser 350 (small-block gas V8) — gas, twin
factory option
A Powerboat Reports used-boat survey reprinted on a Trojan owners' site says some 36s had twin 350 MerCruisers and several owners found them underpowered; one charter operator replaced them with 454 Chevrolet blocks. The survey may cover the later Trojan International F-36 rather than the 1970s boat.Sources: trojanboat.com
Boats of the same model can differ — check which engines yours actually has before ordering parts.
Generator
“Generator: Onan 6.5 kW Fuel: Gasoline” — broker listing (1987), mapleleafyachtsales.com · “There is an Onan 6.5 KW under the cockpit hatch.” — broker listing (1987), jamisonyachtsales.com · “4.5 Onan Generator needs exhaust pipe” — search excerpt (1978), powerboatlistings.com
No builder option list was found, so it's not known whether a generator was standard or optional.
-
Onan — 6.5 kW, gas
Seen on two 1987 F-36 Convertibles for sale; one says gasoline. A 1978 36 Sport Fisherman lists an Onan 4.5 kW.“Onan 6.5 kW Fuel: Gasoline” — broker listing (1987), mapleleafyachtsales.com · “Onan 6.5 KW under the cockpit hatch” — broker listing (1987), jamisonyachtsales.com
Generators are often replaced or added — check the unit's own plate before ordering parts.
Known problems for this model
-
Teak cockpit sole (through 1976) deck
A teak cockpit sole was standard through 1976 and HMY flags it as a likely problem area to inspect closely.hmy.com
Engines & parts
Crusader 350 / 454 inboard gas V8 parts: good
Factory standard engine — you entered “Crusader 350 hp gas V8 inboard”
GM-based inboard engines; Crusader (now part of Pleasurecraft Marine Engine Co.) still publishes illustrated parts manuals and sells through distributors. Go2marine stocks Crusader manifolds, risers, raw water pumps and ignition parts; Osco and Barr make aftermarket manifolds, and new GM/Crusader base engines are sold by rebuilders.
Parts sources: Crusader Engines, Go2marine (Crusader parts), 1-800-RUNS-NEW (GM & Crusader base engines)
Common problems (1)
-
Clogged or failing manifolds/risers exhaust
Owners find individual risers running much hotter than the others (a sign of internal blockage) and debate replacing vs. flushing; Osco manifolds are often preferred as closest to OEM.marineengine.com · marineengine.com
Maker’s service schedule (14)
| Engine oil & filter change 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 50 hrs or 1 yr | “Change engine oil and filter — After 1st 25 Hrs / Every 50 Hours of Operation / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Fuel filters & water separator 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 50 hrs or 1 yr | “Fuel Filters - Service or replace — After 1st 25 Hrs / Every 50 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Raw-water pump impeller 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Cooling System - Inspect/Replace raw water pump impeller — Every 100 Hours of Operation / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Drive belts inspect / replace 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Drive Belt - Inspect condition and check tension — After 1st 25 Hrs / Every 100 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Spark plugs inspect / replace 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Ignition System and Spark Plugs - Clean and inspect condition — After 1st 25 Hrs / Every 100 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Exhaust mixing elbow inspection 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 4 mo | “Exhaust System - Check condition and tightness of all hose clamps — After 1st 25 Hrs / Every 100 Hours(1) / Once Each Ye” — manufacturer (2013), crusaderengines.com |
| Coolant replacement & freeze-point test 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 5 yrs | “Fresh-water cooled models - Change coolant — Every five years” — manufacturer (2013), crusaderengines.com |
| Engine pencil zincs 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 1 mo | “Zinc Anodes - Heat exchanger and cooler - check condition — Every 30 days” — manufacturer (2013), crusaderengines.com |
| Transmission fluid change 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 1 yr | “Transmission and "V" Drive - Change fluid and clean strainer, if equipped — After 1st 25 Hrs (Hurth Only) / Once Each Ye” — manufacturer (2013), crusaderengines.com |
| Flame arrestor & crankcase ventilation - clean and inspect 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Flame Arrestor and Crankcase Ventilation System - Clean and inspect — Every 100 Hours / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Engine alignment check 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 1 yr | “Engine Alignment - Check and adjust if necessary — After 1st 25 Hrs / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Inspect all hoses (and cooling hose clamps) 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 1 yr | “Hoses (all) - Inspect for cracks, swelling, weather checking or other signs of deterioration — Every 100 Hours / Once Ea” — manufacturer (2013), crusaderengines.com |
| Shift & throttle cable linkage - inspect and lubricate 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 100 hrs or 4 mo | “Shift and Throttle Cable Linkage - Inspect and lubricate — Every 100 Hours(1) / Once Each Year” — manufacturer (2013), crusaderengines.com |
| Electrical system - check connections and wiring 2013 MPI 5.0L/5.7L (350 CID)/6.0L | 50 hrs or 2 mo | “Electrical System (complete) - Check for loose or dirty connections and damaged wiring — Every 50 Hours(2) / Once Each Y” — manufacturer (2013), crusaderengines.com |
Service part numbers (18)
| Oil filter remote-mounted oil filter (MP7.4L and 2013 5.0/5.7/6.0L MPI) |
Crusader 22679 | “Oil Filter 22679 (MAINTENANCE ITEM PART NUMBERS)” — manufacturer, crusaderengines.com |
| Fuel filter MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008 |
Crusader 47038 | “Fuel Filter 47038 (MAINTENANCE ITEM PART NUMBERS)” — manufacturer, crusaderengines.com |
| Fuel filter 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13 |
Crusader RP080026 | “Fuel Control Cell (FCC) Fuel Filter Element RP080026” — manufacturer, crusaderengines.com |
| Fuel pre-filter / separator MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: engine-mounted Racor water-separating filter 47046 |
Crusader 47047 | “25 47047 Element, Racor fuel filter (Not Shown) 1” — manufacturer, crusaderengines.com |
| Fuel pre-filter / separator 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13: primary fuel filter |
Crusader R080033 | “Primary Fuel Filter Element R080033” — manufacturer, crusaderengines.com |
| Raw-water impeller MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008 (raw water pump RA057031) |
Crusader RP061017 Replaces R061017 |
“Replaces Crusader R061017 (Impeller Kit with Gasket & O-Ring | Crusader RP061017)” — dealer, marinepartssource.com · “Replaces Crusader R061017 (Impeller Kit with Gasket & O-Ring | Crusader RP061017)” — dealer, marinesuppliesdepot.com |
| Raw-water impeller 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13 |
Crusader RP061022 | “Impeller , Raw Water Pump (1) RP061022 (ON-BOARD PARTS KIT 5.7L)” — manufacturer, crusaderengines.com |
| Raw-water pump kit MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008 (raw water pump RA057031) |
Crusader 40064 | “40064 Overhaul Kit, Major (includes items 2, 3, 11, 14 and 15)” — manufacturer, crusaderengines.com |
| Drive belt MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: alternator drive |
Crusader 98210 | “Alternator Drive Belt 98210” — manufacturer, crusaderengines.com |
| Drive belt MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: raw water pump drive |
Crusader 10258 | “Raw Water Pump Drive Belt 10258” — manufacturer, crusaderengines.com |
| Drive belt 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13, left-hand (LH) rotation: serpentine |
Crusader R066028 | “Belt , Serpentine (1) R066028 (ON-BOARD PARTS KIT 5.7L (LH))” — manufacturer, crusaderengines.com |
| Drive belt 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13, right-hand (RH) rotation: serpentine |
Crusader R066029A | “Belt , Serpentine (1) R066029A (ON-BOARD PARTS KIT 5.7L (RH))” — manufacturer, crusaderengines.com |
| Spark plug MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: platinum plug |
Crusader 49078 × 8 | “Spark Plugs (platinum) 49078” — manufacturer, crusaderengines.com |
| Spark plug 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13: platinum plug set |
Crusader RP030010 | “Spark Plug , Set, (Platinum) (1) RP030010 (ON-BOARD PARTS KIT 5.7L)” — manufacturer, crusaderengines.com |
| Thermostat MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: raw-water (standard) cooling, 143 F |
Crusader R026002E | “6 R026002E Thermostat (143-degree) 1 (Raw Water Cooling Components - Figure 18)” — manufacturer, crusaderengines.com |
| Thermostat MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: fresh-water (closed) cooling kit, 170 F |
Crusader 98203 | “5 98203 Thermostat (170-degree) 1 (Fresh Water Cooling Components 1)” — manufacturer, crusaderengines.com |
| Zinc / anode MP7.4L / MP454 XLi (454 MPI) - illustrated parts manual L510008: oil cooler / transmission cooler / heat exchanger |
Crusader R168005 | “24 R168005 Zinc, sacrificial 1 (Raw Water Cooling Components - Figure 18)” — manufacturer, crusaderengines.com |
| On-board spare parts kit (belt, cap, rotor, fuses, relays, plugs, impeller, fuel filters) 5.7L (350) MPI with FCC fuel system, 2007 on - 2013 owner manual L510001-13, LH rotation |
Crusader RK173089D-07 | “ON-BOARD PARTS KIT 5.7L (LH) 2007 TO PRESENT, FCC FUEL SYSTEM RK173089D-07” — manufacturer, crusaderengines.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
MerCruiser 5.0 (305) / 5.7 (350) V8 gas parts: good
Factory optional engine — you entered “MerCruiser 350 (small-block gas V8)”
GM small-block Chevrolet base engines, so internal parts are everywhere. Marine exhaust manifolds and risers for 1983–2002 small blocks are sold by many aftermarket makers (Sierra, Barr, Osco and others) through Power Boat Supply, Hardin Marine, Basic Power Industries and similar stores; Mercury sells genuine parts through dealers.
Parts sources: Power Boat Supply, Hardin Marine, Basic Power Industries
Common problems (2)
-
Manifold/riser failure and water in cylinders exhaust
Cast-iron manifolds and risers rust internally or their gaskets fail, letting water back into the cylinders; small amounts cause hard starting and rough running, large amounts hydrolock and wreck the engine. Service roughly every 7 years in fresh water and about 5 in salt.powerandmotoryacht.com · forums.iboats.com · justanswer.com
-
Overheating from scaled manifolds cooling
Rust and scale inside the manifolds restrict cooling flow and cause overheating under load.powerandmotoryacht.com
Maker’s service schedule (8)
| Engine oil & filter change | 100 hrs or 1 yr | “Most four-stroke outboards and sterndrive engines require an oil change either annually or every 100 hours of operation.” — manufacturer, mercurymarine.com |
| Fuel filters & water separator | 100 hrs or 1 yr | “The fuel filter on your engine should be inspected or replaced per the maintenance schedule in your owner's manual, usua” — manufacturer, mercurymarine.com |
| Raw-water pump impeller | 300 hrs or 3 yrs | “How often should my seawater pump impeller be serviced? Every 300 hours or 3 years, whichever comes first.” — manufacturer, mercurymarine.com |
| Spark plugs inspect / replace | 300 hrs or 3 yrs | “How often should spark plugs be changed? Every 300 hours or 3 years, whichever comes first.” — manufacturer, mercurymarine.com |
| Coolant replacement & freeze-point test closed (freshwater) cooling only | 5 yrs | “How often should coolant be changed on engines with closed cooling? Every 5 years.” — manufacturer, mercurymarine.com |
| Transmission fluid change sterndrive gear lube | 1 yr | “Gearcase lubricant in outboard and sterndrive lower units should also be changed annually or at the service interval spe” — manufacturer, mercurymarine.com |
| Lubricate steering linkage and check power-steering fluid sterndrive | 100 hrs or 1 yr | “Mercury Marine recommends lubricating the steering linkage and checking the power steering fluid level in ... MerCruiser” — manufacturer, mercurymarine.com |
| Check power trim fluid level sterndrive | 100 hrs or 1 yr | “Power trim and tilt fluid level should be checked annually or every 100 hours.” — manufacturer, mercurymarine.com |
Service part numbers (6)
| Oil filter | Mercury Quicksilver 35-866340Q03 | “Part number: 866340Q03 ... for MerCruiser sterndrive and inboard engines except V6 engines with the oil filter mounted o” — manufacturer, mercurymarine.com · “Includes: Oil Filter Oil Filter 866340Q03 Fuel Filter 802893Q01 ...” — dealer, midnightmarine.net |
| Fuel filter carbureted engines (Rochester 2-/4-barrel, MerCarb 2-barrel): filter inside carburetor fuel inlet |
Mercury 53336T | “For use on MerCruiser 3.0L, 4.3L, 5.0L , 5.7L and 7.4L engines with Rochester 2- and 4-barrel and MerCarb” — manufacturer, mercurymarine.com |
| Fuel filter MPI engines with Gen III cool fuel module (filter page: 2004 and newer; kit page: 2002 and newer) |
Mercury Quicksilver 35-8M0093688 | “Fits 2004 and newer Mercury/MerCruiser sterndrive and inboard engines with Gen III (3) fuel cooler” — manufacturer, mercurymarine.com |
| Raw-water impeller Bravo sterndrive and inboard engines with engine-mounted sea water pump (2-piece plastic pump per Mercury) |
Mercury Quicksilver 47-59362Q01 Also: Sierra 18-3087 |
“For MerCruiser engines with engine mounted, 2-piece, plastic sea water pumps.” — manufacturer, mercurymarine.com · “Water Pump Impeller 59362Q01” — dealer, midnightmarine.net |
| Thermostat standard cooling, 160 F |
Mercury Quicksilver 807252Q5 | “Thermostat 807252Q5 is for V6 and V8 MerCruiser engines ... made by General Motors (model year 1987-2016)” — manufacturer, mercurymarine.com |
| 100-hour maintenance kit (oil filter, fuel filter, drive seals) MPI engines with Gen III cool fuel module (2002 and newer) |
Mercury 8M0147053 | “Mercury 8M0147053 MerCruiser 5.0L, 5.7L, 6.2L, 8.1L and 8.2L V8 MPI ... 100 Hour Maintenance Kit” — manufacturer, mercurymarine.com |
From the engine maker’s parts lists, or two independent parts dealers. Numbers change with serial number and get superseded — check yours before ordering.
Model sources (5)
hmy.com · web.archive.org · trojanboat.com · mapleleafyachtsales.com · jamisonyachtsales.com
Other Trojan models
- Trojan 10 Meter Sedan 1982–1989
- Trojan 32 Sedan (F-32) 1973–1991
Researched from public sources. Spotted an error? The sources are listed above — tell us what they got wrong.